our Products

Agricultural Pumps > SS submersible > 6'' SS Submersible Pumps > 60m³/h

About the Product

Point Stainless steel Submersible Pumps are ingeniously designed and developed employing latest engineering softwares, high-tech machinery of pumping technology to deliver the best possible hydraulic efficiency . All these pumps are made of corrosion resistance Stainless steel with Non return valve. These pumps are made by High quality AISI 304 / AISI 316 grade stainless steel.

The 6" Stainless steel Submersible Pumps discharge range from 7m³/hr to 80m³/hr and Head range from 4.5m to 550m. The 6" Stainless steel Submersible Pumps are available with 2", 2½", 3" & 4" Outlet Size.

Point Stainless steel Submersible Pumps are used for Public water supply, Irrigation, Fountains, De-watering, Sprinkler systems, Industrial water supply and Pressure boosting systems.

Features of Point Stainless steel Submersible Pumps: Stainless steel impellers and diffusers to resist corrosion, Built in non-return valve to protect the pump against water hammer, highly efficient, good resistance to sand, Energy efficient hydraulic design for cost effective operation, Easy to install and dismantle for service in the field if necessary .

Pumped Liquids

Non-aggressive, non-explosive, pure, cold, fresh water without abrasives particles having the following characteristics.

Temperature 91.4 F
Chlorine ion density 500 ppm (max.)
Allowable solids 3000 ppm (max.)
Specific gravity 1.004 (max.)
Hardness (Drinking Water) 300 (max.)
Viscosity 1.75x106 m²/sec (max.)
Turbidity 50 ppm silica scale (max.)
pH 6.5 to 8.5
Impellers

Radial flow impellers

4" : PS4S - 1, PS4S - 3 and PS4S - 5
6" : PS6S - 14, PS6S - 18 and PS6S - 22

Mixed flow impellers

4" : PS4S - 14
6" : PS6S - 30, PS6S - 48 and PS6S - 60

Connection

Screwed pipe connection with BSP thread as standard
NPT thread pipe connection are avilable on request

Curve Conditions

The conditions below apply to the curves shown the following pages.

Common

  • Tolerances in accordance with ISO 9906, Annex A.
  • Test Results with clean cold water, without gas content. Measurements have been made with airless water at a temperature of 20oC
  • Head and power values valid for liquids with density p = 1,0 kg/cm3 and kinematic viscosity v = max 1 mm2/s (1cSt)
  • When pumping liquids with a density higher than that of water, motors with correspondingly highter outputs must be used.
  • The QH curves apply to a rated motor speed of 2900 rpm.
  • The performance curves are inclusive of possible losses such as non-return valve losses.
  • A safety margin of +0.5m is recommended for the NPSH range

4" & 6" Curves

  • QH : the curves are inclusive of valve and inlet losses at the actual speed
  • Power curve : the power curve shows pump power input at the actual speed for one stage.
  • Efficiency Curve : n% shows pump stage efficiency.

Operating Conditions

Liquid temperature 0o to + 45oC
Max. sand content into the water 50g/m3
Max. starts per hour 30 at regular intervals
Direction of rotation Clockwise as seen from the pump coupling side.
Impeller / Diffuser

Point PumpsThese pumps are made with SS impeller and Diffuser for high efficiency and less loss. Impellers and Diffusers are avilable with various material grades like AISI 304 / AISI 316.

Shaft

Point PumpsStainless steel pump shafts are designed and made of AISI 304 / AISI 431 grade Stainless steel material.

Non return Valve with body

The integral Non return valve prevents back flow and reduces the risk of water hammer which paves the way for trouble free performance. Non return valve available with various material grades like AISI 304 / AISI 316.

Suction Housing

Point PumpsSuction housing are designed & manufactured in investment casting with various material grades like AISI 304 / AISI 316.

Wearing Ring / Intermediate Bush

Point PumpsThe wearing Ring and Intermediate bush are made with high quality rubber like NBR which has less wear and tear resistance.

Strainer

Strainers are provided in the inlet which prevent the oversized particulars entering inti the pump.

Reliability

Point PumpsReliability is ensured by means of high material standard and process methods. Pump parts are made up of stainless steels. These can withstands high abrasive and corrosive environment. Bush bearing and other rubber components are also designed to withstand sand abration and erosion.

  • Point Pumps
  • Point Pumps
  • Point Pumps
  • Point Pumps
Technology - Pump

The technology of submersible pumps are multistage single suction centrifugal type and provided with integral check valve which can be coupled to a submersible electric motors. The submersible pumps are designed and manufactured to provide smooth and easy installation.

Point submersible pumps can be offered with either Point water filled submersible motors or other NEMA standard motors.

The pump is checked during each stage of the assembly process up to the final stage, where in every pump is checked for flow, pressure, power consumption and leaks.

Material Options

The submersible pumps are available in stainless steel AISI 304 and AISI 316 grade in 4" and 6" submersible pumps.

Pump shaft AISI 304 & AISI 431
Diffuser casing AISI 304 / AISI 316
Impeller AISI 304 / AISI 316
Efficiency

To make a positive impact in the pump efficiency level effective measures have been taken in designing every component. Superior manufacturing methods are adopted to achieve higher efficiencies.

Durability

The best material, high quality manufacturing methods and rigorous safety tests are conducted to ensure superior strength and durability of each product range.

  • Point Pumps
  • Point Pumps
  • Point Pumps
  • Point Pumps
Cross Sectional View
  • Point Pumps
  • Point Pumps
Dimensional Drawing

Dimensional Data
PUMP MODEL REQUIRED MOTOR POWER No. of Cable Guard DIMENSIONS (mm) APPROX NETT. WEIGHT (kg)
kW HP D1 OS L2
PS6S-60/01 2.2 3 1 145 80/100 398 8.0
PS6S-60/02 4 5.5 1 145 80/100 511 10.4
PS6S-60/03 5.5 7.5 1/2 145/149 80/100 624 12.7
PS6S-60/04 7.5 10 1/2 145/149 80/100 737 15.2
PS6S-60/05 9.3 12.5 1/2 145/149 80/100 850 17.6
PS6S-60/06 11 15 1/2 145/149 80/100 963 20.0
PS6S-60/07 13 17.5 1/2 145/149 80/100 1076 22.5
PS6S-60/08 15 20 1/2 145/149 80/100 1189 24.8
PS6S-60/09 18.5 25 1/2 145/149 80/100 1302 27.2
PS6S-60/10 18.5 25 1/2 145/149 80/100 1415 29.6
PS6S-60/11 22 30 1/2 145/149 80/100 1528 32.1
PS6S-60/12 22 30 1/2 145/149 80/100 1641 34.3
PS6S-60/13 26 35 1/2 145/149 80/100 1754 36.6
PS6S-60/14 26 35 1/2 145/149 80/100 1867 39.2
PS6S-60/15 26 35 1/2 145/149 80/100 1980 41.8
PS6S-60/16 30 40 1/2 145/149 80/100 2093 44.5
PS6S-60/17 30 40 1/2 145/149 80/100 2206 46.4
PS6S-60/18 37 50 1/2 145/149 80/100 2319 48.4
PS6S-60/19 37 50 1/2 145/149 80/100 2432 50.4
PS6S-60/20 37 50 1/2 145/149 80/100 2545 52.4
Performance Curves

Performance Table
PUMP MODEL MOTOR KW Ips 0 4.16 5.55 8.33 11.11 13.88 16.66 19.44 22.22
m3/h 0 15 20 30 40 50 60 70 80
PS6S-60/01 2.2 TOTAL MANOMETRIC HEAD IN METRES- (COLUMN WATER) 14 13 12 11 9 7 5 3 1
PS6S-60/02 4 26 25 24 23 20 17 14 10 5
PS6S-60/03 5.5 39 38 37 35 32 27 22 15 9
PS6S-60/04 7.5 52 51 50 47 42 37 31 22 13
PS6S-60/05 9.3 67 64 63 59 53 45 37 28 16
PS6S-60/06 11 82 78 76 71 63 56 47 35 21
PS6S-60/07 13 94 94 89 83 73 66 55 41 24
PS6S-60/08 15 110 104 102 97 87 76 65 48 30
PS6S-60/09 18.5 122 114 112 106 95 84 70 54 33
PS6S-60/10 18.5 138 133 128 118 105 92 76 57 35
PS6S-60/11 22 148 142 138 128 114 101 86 65 40
PS6S-60/12 22 167 156 152 141 124 109 92 69 43
PS6S-60/13 26 180 170 165 153 137 120 100 75 45
PS6S-60/14 26 195 184 179 164 144 128 110 83 48
PS6S-60/15 26 212 198 194 177 157 137 117 85 48
PS6S-60/16 30 220 213 207 188 167 147 127 89 57
PS6S-60/17 30 242 227 222 205 183 160 138 107 63
PS6S-60/18 37 252 240 233 212 189 176 142 112 67
PS6S-60/19 37 270 254 248 231 206 181 152 116 74
PS6S-60/20 37 282 276 267 259 216 189 162 126 80

Refer General Information for performance curve conditions and for other details.
Curve tolerance according to ISO : 9906, Annex - A.